Friday, August 19, 2011

How to use a flip-over Saw


!±8± How to use a flip-over Saw

Preparation and structure

Turn around when you set a saw, it is important that a suitable site, which flat surface free of loose material, dirt, or gravel is the work chosen. Check that the flap was about the company and is not moving.

The power supply from a safe place, with sufficient capacity to start a wave of powerful engine, often around 2000W. This supply should be a sort of short circuit protection, preferably sensitive switch, the tripeven in the event of an accident. When using a 110V transformer, this location was next to the feed point and use an extension cord 110v suitable to turn around. Do not run extension cords 240v to 110v transformer on the visa!

Useful path to flip the power cord over looked away from the work and not exposed in any way from the ground to cause the risk of tripping.

Collect your personal protective equipment (PPE), which should include a minimum of safety glasses andStick with a good drive when you turn the table saw in the cutting mode. Hearing protection is a good idea if in an enclosed space or when using the saw for a long time and absolutely necessary to cut aluminum (special blade required) (may be used as the sound of these blades horrendous!) If not then extraction with nuisance dust masks should be considered especially when ripping down her long fabric panels or working in an enclosed space.

As always wear thick, steeltoe-capped boots, clothing, and put all sensitive loose that could be dragged into the blade. The use of rings and other jewelry is not recommended. Helmets are required when there is a risk of transmitting high or very long wooden head.

Their stocks of material must be prepared by hand and stacked in a safe manner, the removal of a single length should not cause the stack to collapse!

This writer, as being the place, saw that I had to go around and takefreshly cut pieces of work and then stack the material on the left side for convenience. This is a clear link between the bend and looked at the work place. As an efficient means more work for less effort!

When cutting longer lengths, eg, 1 meter, a sort of support will be needed page. It supports both commercial and custom modified saw "saw horses. This writer uses metal folding saw horses with a piece of wooden screwedthe tips so that exactly the same height as the cutting-off "read". Three is ideal, two left and one to get right, the cut-off. Two on the left side is necessary because the material can become smaller when cutting multiple sections of a length. This is a prerequisite for safe working and the blade broke off the piece, such as preventing it from cuts.

Plan your work so that the amount of time that you "flip" the table saw mode and back again to minimize, ifpossible. For example, not all the table saw cuts first and then cuts back to the cutter. This is not always possible or practical, but fortunately most flip saws are ready to change.

Working with a rollover Saw

If you have set as described above are easy to use, efficient and above all safe!

Miter cuts

The material should be placed gently on the flip over saw and skidded to see the area and are cut. Drops sharplyMaterial for the bed finally saw the ruin itself settings precision cutting and can also damage the saw.

Lengths must be selected from the left and short lengths of about one meter below should be marked on the right side. This is to ensure that the longest side of the material to be cut on the left side, does not apply because this is the page that will determine whether the saw does its work.

Place the material under the blade and grab the handle with release blade guard NOT THE PRESSPOWER SWITCH at this point.

Pull the saw until the blade almost touches the material and put the material back and forth until the blade, the waste / cutting on site is your brand positioning.

Leave the saw at his place of rest and maintain a firm grip on the piece, start the engine.

Waiting to go to the blade at full speed, to hear him. Familiar with the operation of the engine sounds like something unusual and to be vigilant. Sometimes there are small piecesMaterial captured in the mechanism of guard and can rub against the blade until the fly without prior notice! Stop, pull the plug and check for unusual noises now!

With the blade at full speed and plays well, gently pull the saw down into and through the piece. Familiarize yourself with the judge, as the blade cuts and feels, to learn how to apply pressure to slow down too much and the blade, about 10% or so is about right. Once all the way through the material,Given the delicacy back into its upright position, turn the engine off and wait for the blade to stop completely.

All done, you should now have the correct size of the piece. Ready for transfer to the workplace for the attachment.

Let me have you seen a run-in between the maximum cuts. On a busy site running engine can be dangerous and deceptive calm.

Saw cuts

Swing the "head" and as safe as the manufacturer's instructions (which vary a little ') is directed, "Flip"has seen more and you start to hear clicking on the localizer. Always 'see' that the saw is determined visually to bed position.

Always use the riving knife and blade protection when ripping down wood, according to the manufacturers description. This keeps the connection of the blade after cutting wood and prevents 'launch' the blade of the wood back at you with some speed!

Align the fence or to lead, when a cut parallel with the degree markings on the table saw or read by measuringbetween the fence and the blade with a tape measure.

When you need to set the saw on previous statements that you saw before turning down a free surface (it's so tempting to stack the material behind you, but as you can see, this is an error).

Once done, start the saw you turn around and take a step back from the machine with the material at hand. Even for the motor as the blade rotates to hear in full swing and place your material on the front edge of the table and the linewith the fence.

Meanwhile, the blade is running at full speed, gently but firmly bring the material of the blade and keeps company with a laterally and downward pressure on the material in the guide fence and table. If you're about half way you should discontinue the ability to drag the material, end to end turn around and do the other half until you make the first cut. Lengths can be directly powered through in one sitting, keep your hands away from the blade or use aor two sticks thrust.

Personally, this writer is not like going closer to a blade of about 100 mm or 4 to get "sure I know many who run much closer than that, but hey, I like all my fingers!

Cut management

Always know where your cut will be. Small pets can fly, if not properly managed, and cuts far the tip of the blade trap and even problems. Good support is the answer before, during and after the cut.

Limitations

Assuminghave the right size saw for the job in hand and can be physically cut the material. The only restriction is that you have seen with a rollover to find, is that the machine with constant rotation between the two modes if the job requires it or if you do not really plan your cuts. To flip over as you look a little 'ahead and think about what to do.

As with many combination machines, there is a compromise in order to achieve flexibility. TurningSince this may mean that the table saw is a small bed, or the ability of the miter saw is a bit 'less because they do not have a sliding arm.

Ultimately, however, can be seen with a simple rollover coupled with good ability and versatility that has seen a rollover handle most jobs on the spot or in the garage.

Further Reading

Amazon store hundreds of books on this subject, looking for chain saws, miter saws and table saws for the bestResults.

Evaluations may at sites of supplying these days to find.

Conclusions

Choose a suitable place to set and secure the saw itself, ideally separated from other workers.

Make sure that the rollover was on a stable surface and not moving.

Use a safe, caring and sensitive cable management .*

Make sure that "push stick" and personal protective equipment (PPE) at hand.

Organize the materials at hand and safely stacked on the left (before the saw).

Get your way with the turning point seemed to the workplace is logical, clear and secure.

Plan your work, job sharing in the miter saw and how.

Page is supported when using a material of meters in length.

Material mark to the left, when the average less than one meter, then in the right place.

Hold the workpiece firmly and not allow the blade to touch the material up to full speed.

Let me run through the saw cuts.

Always usethe riving knife and blade protection when ripping down the material.

Hold hand / finger and the execution of at least 100 mm away from a blade.

Thoroughly clean sawdust and store for next time.

Clean the blade with a light oil, if not with the saw again for several weeks.

Hold the saw and saw the room closed storage in an old sheet or blanket.

Warnings

The power supply must be protected by a safe place, with sufficient capacity to increase the commissioninga powerful engine, often to 2000W.

When using a 110V transformer, this location was next to the feed point and use an extension cord 110v suitable to turn around. Do not run extension cords 240v to 110v transformer on the visa!

Useful path to flip the power cord over looked away from the work and not exposed in any way from the ground to cause the risk of tripping.

Collect your personal protective equipment (PPE), which should include at least suitableGlasses and a stick with a good drive when you turn the table saw in the cutting mode.

Hearing protection is a good idea if in an enclosed space or when using the saw for a long time and absolutely necessary to cut aluminum (special blade needs, like the sound of these blades horrendous!)

Considered nuisance dust masks, if not with a dust collector.

As always wear thick, steel toe-capped boots, clothing, and sensitive may put all loosepulled into the blade.

The use of rings and other jewelry is not recommended.

Helmets are also required if there is a risk of transmitting high or very long wooden head.


How to use a flip-over Saw

Top 10 Popular Karaoke Song 110 220 Voltage Converter Top Quality




No comments:

Post a Comment


Twitter Facebook Flickr RSS



Français Deutsch Italiano Português
Español 日本語 한국의 中国简体。







Sponsor Links